Cooling - Controlling water temperature

The introduction of the Cooper S proved to be a testing time for the Mini’s systems, but conveniently provide a guideline as to what the standard cooling system was capable of - that used on the ‘S’ was marginal to say the least!

It wasn’t uncommon for many S’s to spew water from their overflow pipes when ever it was doing anything other than a steady 70 miles an hour, over-heating eventually caused through water loss. Perhaps some deductions can be made from the following…

There are a number of elements involved in controlling water temperature. Some confusion over what to sort first when over-heating occurs leads to wasted time and money, and possibly terminal engine damage. Maximum power is usually generated from A-series engines at 70 – 75 degrees C (160 to 170 degrees F). The main problem with this on a road car is the oil’s unlikely to get hot enough for maximum performance – the results outlined previously.

Engine transplants - Ancillary parts

Engine mountings are a whizz to fit as the Mini ones fit straight onto any of the other units. Just remove the Metro/AA/1300GT ones and swop the mounts over from the Mini unit. If they’re split, fit new ones, they’re cheap.

Terminology -
BBU - Big Bore Unit
SBU - Small Bore Unit

NOTE: This information covers transplanting large-bore engine units into small-bore engined Minis. For further information for exact differences between pre-A+ and A+ units, see relevant separate article.

Engine mountings and steady bars.
Engine mountings are a whizz to fit as the Mini ones fit straight onto any of the other units. Just remove the Metro/AA/1300GT ones and swop the mounts over from the Mini unit. If they’re split, fit new ones, they’re cheap. If using the AA/1300GT unit - it's advisable to cut off the 'wings' on the front plate that carried the engine mounts on the radiator end.

C-ARA4442, C-ARA4443, C-ARA44443 HI PERFORMANCE RADIATORS

These radiators were developed to provide superior cooling capability over the standard equipment where non standard engines are being used.

C-GRH1465 SILICON TOP HOSE FOR TWINPOINT CARS

To fit this silicon top hose you might need to remove the grille and dip the spot lamp down for access to the engine bay.

The hose fits on the thermostat quite easy but because the radiator is bush mounted and has plastic outlets with large lips extra care is required to push the hose into place. This is why we recommend grille removal. Align the hose up correctly to the radiator outlet lip to push it on and the addition of some washing up liquid to the inside of the hoses will help it slide on easier. Do not over tighten the clips on the radiator.

MINI ENGINE STABILISER MSSK1000

1. This is an auxiliary steady bar kit and should not be used to replace any other standard fitment parts that have broken.

2. Remove the radiator support bracket from the radiator and the thermostat housing.

3. Slacken the nut retaining the exhaust manifold at the radiator end of the engine.

4. Remove the three bolts securing the bulkhead blanking plate as shown in the diagram. If the car has a heater pipe as indicated on the diagram then this should be disconnected at the engine.

MINI ENGINE STABILISER MSSK1300

1. This is an auxiliary steady bar kit and should not be used to replace any other standard fitment parts that have broken.

2. Remove the radiator support bracket from the radiator and the thermostat housing.

3. Slacken the nut retaining the exhaust manifold at the radiator end of the engine. Remove the exhaust manifold stud by tighterning another nut against the original manifold nut and then screwing the nut out of the cylinder head.

4. Remove the three bolts securing the bulkhead blanking plate as shown in the diagram. If the car has a heater pipe as indicated on the diagram then this should be disconnected at the engine.

C-GRH240 C-GRH247 C-GRH1006 SILICONE HOSES

This hose has been designed to fit any pre 1989 Mini where the heater valve is bolted on the cylinder head. Later cars had an in-line valve and different plumbing.

C-GRH240 BOTTOM HOSE

1. This hose has been designed to fit...

Choice of radiators

Choice of radiators

Radiators Read about heat conductivity, core, fin design, tube sizes and design changes

Monitoring Radiators development since 1960.

Monitoring Radiators development since 1960.

I have been monitoring radiators and their development since the late 1960’s because they were and still can be a problem when tuning cars.
I have seen, tried and tested everything made available or offered to Mini Spares

Historical Article - March 1992 - Wild Thing!

In 1988, a humble 1973 Mini 1000 was minding its own business somewhere in London, when along came a young Mini freak called Jason King, who wanted to change it for ever, and make it famous.

Jason persuaded the owner to take £450 for the car, and then proceeded to throw £12,000 worth of presents at it for the next 3 years. Every minute of Jason’s spare time was spent working on his new car and every minute of his working time was spent looking for spares.

Historical Article-February 1995-Keeping Your Cool

Keeping Your Cool This is the time of year when people suddenly wake up to the fact that it is getting mighty cold, and had therefore better do something about the car's cooling system before it freezes up....

Historical Article-February 1995-Keeping Your Cool

Keeping Your Cool This is the time of year when people suddenly wake up to the fact that it is getting mighty cold, and had therefore better do something about the car's cooling system before it freezes up....

Historical Article-February 1995-Calver's Clinic

Calver's Clinic COOKING OIL This engine oil thing seems to have caught people's attention - which is good as there is nothing like awareness of what is good for your engine. Having done the 'Life Blood' article in Minitech News 6, and what oils to avoid in Mini Tech News 7.

Historical Article-February 1995-Calver's Clinic

Calver's Clinic COOKING OIL This engine oil thing seems to have caught people's attention - which is good as there is nothing like awareness of what is good for your engine. Having done the 'Life Blood' article in Minitech News 6, and what oils to avoid in Mini Tech News 7.